Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair Services in Sherman Oaks, CA
A gate that won’t open or won’t stay closed in Sherman Oaks usually comes down to one of three things: a burnt-out operator motor, a sagging hinge post, or a limit switch knocked out of alignment by the heat. You’ll find all three on any given week in this part of the San Fernando Valley, and most of them can be fixed the same day we look at it. Call (951) 749-5734 and you’ll get a live person who knows Sherman Oaks streets, not a phone tree.
Hal Gatewood has been fixing gates since 2001, and he still takes the calls himself. When your swing gate stops mid-arc on Valley Vista Boulevard or your slide gate grinds against its rail near Dixie Canyon, you want someone who has already seen that exact failure a hundred times. That’s us.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Why Sherman Oaks Homeowners Choose Gatewood Fence & Gate
Most gate companies in Los Angeles will quote you a replacement before they’ve even looked at the hinge. We don’t work that way. Our first question on any Sherman Oaks call is whether the gate can be repaired in place, because a well-built iron gate from the 1980s usually has better steel in it than anything you’d buy new today. We weld on site, in your driveway, and we don’t haul anything off to a shop unless it genuinely cannot be fixed where it stands.
Homeowners in the Chandler Estates and Ridgewood Hills areas call us because the name on the invoice is the name on the shop. Hal Gatewood is the owner, the license holder, and the person who stands behind the 90-Day Done Right Promise that comes in writing with every job. We’re state-licensed and insured, background-checked, and we stock parts for nine major gate brands on the truck so we don’t have to make a second trip. We serve the valley floor off Van Nuys Boulevard, serving Van Nuys, CA, and the hillside streets climbing toward Mulholland with the same attention, because the failures are different in each.
Every call is answered by a live person, 24 hours a day, 7 days a week. That’s not a call center in another state. That’s our crew, awake because your gate failed at 6:00 a.m. and you can’t get your car out.
Gate Repair Services We Offer in Sherman Oaks
Gate Repair
A sagging gate in Sherman Oaks is almost never a problem with the gate itself. The hinge post moves, the gate follows, and the latch stops lining up. We reset posts, rebuild hinges, straighten frames, and weld cracks rather than telling you to buy a new gate.
Learn more about our gate repair services in Sherman Oaks.
Gate Installation
When a gate has rusted through at the bottom rail or the post is rotted past saving, a new gate makes sense. We measure, order, and install with the operator sized to the actual slope and weight, not a flat-spec guess. It’s scheduled work, quoted in writing before any metal is ordered.
Learn more about our gate installation services in Sherman Oaks.
Gate Motor & Opener
In Sherman Oaks heat, operator motors burn out faster than you’d expect, especially on hillside driveways where the unit works against gravity every cycle. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, and we carry the common failure parts on the truck. If the motor is beyond saving, we replace it with a unit rated for the grade it’s actually on.
Learn more about our gate motor and opener services in Sherman Oaks.
Gate Access Control
Keypads, intercoms, vehicle detectors, and phone-entry systems all fail eventually, and a gate that opens for everyone is just a decorative fence. We diagnose access control problems and fix or replace only what’s broken, whether it’s a keypad on Sepulveda Boulevard or a whole condo-entry system off Ventura Boulevard.
Contact us for Gate Access Control - Sherman Oaks repair and installation.
Gate Parts & Welding
Most “irreparable” gate damage is just a broken weld someone didn’t want to make. We’re set up to weld on site, which means your gate stays in your driveway and the fix gets done in hours, not weeks. Hinges, pickets, frame corners, operator mounts, catch posts; if it’s steel, we can put it back.
Ask about Sherman Oaks Gate Parts & Welding services when you call.
Neighborhoods We Serve in Sherman Oaks
We run calls all over Sherman Oaks and nearby Encino, CA, from the flat ranch-tract streets north of Ventura Boulevard up into the canyons south of it. A gate problem in the hills usually involves slope, heat, and an undersized operator, while a gate problem on the valley floor is more often old hardware and shifted posts. We know the difference before we pull up.
- Chandler Estates - mostly 1950s-60s ranch homes with original or 1980s-era gate hardware.
- Ridgewood Hills - steep driveways where grade-rated operators are the whole game.
- Sherman Oaks Hills - custom homes with heavy architectural gates and long operator run times.
- Valley Glen border streets - mixed housing stock and older slide gates that need frequent rail work.
- Dixie Canyon area - canyon-adjacent lots where Santa Ana winds stress hinge hardware hard.
Typical response time anywhere in Sherman Oaks is same-day for a repair call, and emergency after-hours calls are answered by a live person, not a machine.
Why Sherman Oaks’s Climate & Housing Affect Gate Repair
Sherman Oaks sits in the hottest part of the San Fernando Valley, where summer highs routinely pass 105°F. That heat does two things to automatic gates: it burns out operator motor windings faster than coastal Los Angeles sees, and it makes metal gates expand enough that a limit switch set perfectly in January suddenly lets the gate overtravel in August. Homeowners on the valley floor call about gates that won’t stay closed; homeowners in the hills call about gates that stall halfway up the driveway. Both problems come back to heat and grade, and both are fixable by someone who knows Sherman Oaks conditions rather than treating every gate like it lives in Santa Monica.
The housing stock makes this predictable. Sherman Oaks has a huge base of 1950s-through-1970s ranch-style homes that had wrought-iron swing and slide gates added during the security gate boom of the 1980s and 1990s. That means much of the installed base in the area is now 30 to 40 years old, cycling through its second or third operator. In the hills south of Ventura Boulevard, the original operators were often flat-spec units installed on 8 to 12 percent driveway grades, and the constant gravitational load strips gearboxes in a way flat-valley techs almost never see. When we show up to a hillside Sherman Oaks gate with a stripped gearbox, the fix is a slope-rated unit and a remounted operator, not a like-for-like swap.
Then there’s the Santa Ana season. Fall winds out of the canyons hammer gates on the south slope, slamming limit switches and flexing hinge posts. A gate that worked fine all summer suddenly won’t close in October. We plan for it, and we stock the parts for it.
Pricing for Gate Repair in Sherman Oaks
You’ll always get a number before we start work, and that number doesn’t change at the door. Here’s what Sherman Oaks homeowners can expect to see on a typical repair invoice:
- Service call / diagnosis: No trip charge inside Los Angeles County; diagnosis time is built into the repair quote.
- Hinge post reset or weld repair: $180-$400 depending on post condition and gate weight.
- Operator motor replacement (parts and labor): $450-$900 depending on brand and whether it’s a swing or slide unit.
- Limit switch, receiver, or keypad replacement: $150-$350 per component.
- Full operator swap on a hillside grade: $900-$1,800 when a slope-rated unit and re-mount are required.
The quote is agreed before any work begins, in writing. And we honor a few standing offers with no haggling: $40 off any repair over $200, a free second opinion on any written estimate from another company, and a permanent 10% discount for seniors and veterans. Call (951) 749-5734 for an exact quote on your gate; estimates are free.
Service Area - Cities Near Sherman Oaks
We work throughout the San Fernando Valley and the neighboring communities. If you’re in the broader Los Angeles area or specifically in Van Nuys, Encino, Studio City, or Tarzana, the same owner-operated crew, the same 90-Day Done Right Promise, and the same live-answer phone line cover you. Scheduling is coordinated from our Los Angeles office, and crews serve Sherman Oaks locally.
Serving Sherman Oaks, CA - Our Local Coverage Area
We’re based in the Sherman Oaks area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Sherman Oaks
Most Sherman Oaks gate repairs fall between $180 and $900 depending on whether it’s a weld, a hinge post, or a full operator replacement. A simple limit switch or keypad fix starts around $150, while a complete slope-rated operator swap on a hillside driveway can reach $1,800. You get a written quote before any work starts, and the price doesn’t change at the door. Call (951) 749-5734 for a free estimate on your specific gate.
Yes, in most cases we can. We carry the most common failure parts for LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule on the truck, so a straightforward repair on the Sherman Oaks valley floor is often done in one visit. Hillside jobs that require a slope-rated operator sometimes need a second trip for the part, but we’ll tell you that on the phone before we come out. Call (951) 749-5734 and we’ll give you a straight answer about today’s schedule.
Heat is the main culprit. Sherman Oaks summer temperatures routinely exceed 105°F, which shortens motor winding life and causes thermal expansion in metal gates that throws limit switches out of adjustment. On hillside streets south of Ventura Boulevard, many original operators were undersized for the driveway grade, which means the motor has been working against gravity every single cycle for decades. That’s not a maintenance failure; it’s a spec failure. We fix it with slope-rated equipment and proper mounting.
In most cases, yes, and we do it on site. A broken weld at a hinge or a cracked frame corner doesn’t mean the gate is scrap. We bring the welding rig to your driveway and make the repair where the gate sits, which saves you the cost and hassle of a gate removal and shop visit. If the steel around the weld is rusted too thin to hold, we’ll tell you that honestly and show you why before recommending replacement. Call (951) 749-5734 and describe the damage; we’ll tell you what’s realistic.
We do. Swing gates are more common on the flat ranch-tract streets north of Ventura Boulevard, where there’s room for the arc. Slide gates show up more on hillside properties where a swing gate would hit the driveway grade or block the street. We service both, and we stock repair parts for the nine major brands we’re certified on: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Call (951) 749-5734 to schedule service for either type.
Call Gatewood Fence & Gate for Gate Repair in Sherman Oaks
If your gate is sagging, grinding, stalling, or refusing to open, call (951) 749-5734 now. You’ll talk to a live person who works on Sherman Oaks gates every day, and you’ll get an honest answer about what’s wrong, what it costs, and whether we can fix it today. The quote is free, it’s in writing, and it doesn’t change. Hal Gatewood’s name is on the work, and the 90-Day Done Right Promise means if it’s not right, we’re coming back. That’s how we’ve done it since 2001.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Los Angeles and the San Fernando Valley since 2001.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Sherman Oaks Customers Say
"He came out in the snow to get our gate closed after a delivery lorry clipped it, then came back in the spring to do the proper repair when the ground had thawed. Only charged for the second visit."
- Ingrid Solheim"Safety photo eyes on our old gate had been bypassed by whoever serviced it last, which he was genuinely annoyed about on my behalf. Fitted proper sealed ones and wired them the way they should be."
- Otis Redmond"Hundred and forty feet of cedar privacy fence, all posts set in concrete, all of it dead level on ground that is anything but. He walked the line with me twice before a single hole was dug."
- Judith Stallworth