Linear Gate Repair Nationwide | Gatewood Fence & Gate

Linear Gate Repair in Van Nuys: What to Know First

Linear gate repair in Van Nuys typically runs between $180 and $450 for most operator and hinge fixes, with most jobs finished the same day we start. We’re an independent Linear service provider, not a factory rep, which means we diagnose the actual fault instead of pushing a swap-out. If your Linear operator is dead, grinding, or reversing on its own, call (951) 749-5734 and we’ll tell you honestly whether it’s worth repairing before we ever schedule the truck.

Call (951) 749-5734

This page is for Van Nuys homeowners with a Linear gate opener or Linear-branded gate hardware that’s failed, acting up, or just gotten sloppy. We’ll cover the failures we see most, what they cost to fix, and why Linear jobs in this part of the Valley have their own quirks.

How Linear Products Fail - and How We Fix Them

• Linear LDO series swing openers: capacitor failure after valley heat cycles. The LDO50 and LDO33 use a start capacitor that sits inside a sealed operator housing. After enough Van Nuys summers with daytime highs over 95°, that cap dries out and the arm either hums without moving or trips mid-travel. We replace the capacitor with a higher-temp-rated aftermarket unit and the operator keeps running. The factory part would just cook again.
• Linear APeX and MegaCode receivers losing signal range. If your remote only works from 10 feet away, it’s usually not the remote battery. The receiver board in older Linear APeX units drifts off-frequency as components age. We test the board, reflow the cold solder joints where the antenna attaches, and in most cases we don’t have to replace the receiver at all. That’s the difference between a $60 repair and a $300 part.
• Linear gate hinges and posts on the SL series slide gates. The SL slide gate tracks get bent when the gate’s guide rollers wear out and the gate starts riding on bare metal. By the time the operator’s struggling, the track is already grooved. We straighten what’s salvageable, replace the rollers, and re-align the operator chain tension. If the post has shifted in the soil, we address the post before touching the electronics, because a gate that doesn’t sit level breaks every operator attached to it.
• Linear arm actuators stripping internal gears on dual-gate setups. When one leaf sags even half an inch, the Linear actuator on that side works against gravity every cycle. The brass drive gear inside strips over time, and then the operator clicks but won’t move the leaf. We realign the gate leaf and hinge post first, then rebuild the actuator gearbox. Skip the realignment and you’ll strip the new gear in two months.
• Linear photo-eye safety edges failing from irrigation overspray. In Van Nuys, sprinkler heads aimed too close to the gate soak the photo-eye wiring and the safety edge contacts. Linear’s edges are foam-filled and once water gets in, the contact strip corrodes and the gate refuses to close, or closes on a car. We replace the edge with a sealed aftermarket version and reroute the wiring out of the spray path. It’s a cheap fix that saves the control board from false faults.

Our Linear Gate Repair Process

1. 1
   You call, a person answers. Not a voicemail, not a robot. We ask what the gate is doing, get your address, and schedule a window we’ll actually keep.
2. 2
   We show up and diagnose on site. We test the operator, the board, the remote, the safety eyes, and the hardware, usually within 30 minutes. You’ll know what’s wrong and what it costs before any repair starts.
3. 3
   Parts decision, made with you. We use OEM Linear parts when they’re the right call, and quality aftermarket when they’re genuinely better for the application, like high-temp capacitors and sealed safety edges. We tell you the difference and let you decide.
4. 4
   We fix it in your driveway. We weld on site, straighten tracks, rebuild actuators, and replace boards right there at your gate. Your gate doesn’t leave your property.
5. 5
   We test the full cycle at least five times. Open, close, obstruction reversal, remote range, and edge sensitivity. We don’t call it done until the gate behaves the way Linear designed it to.
6. 6
   You get the 90-Day Done Right Promise in writing. If it fails again within 90 days, we come back and make it right. No re-quote, no argument.

What Linear Gate Repair Costs in Van Nuys

Here’s what we typically see on Linear jobs in Van Nuys:

• Capacitor replacement on LDO series: $90-$150
• Receiver board repair (solder reflow, no part): $60-$110
• Complete operator rebuild with chain/gears: $280-$450
• Safety edge replacement (sealed aftermarket): $140-$220 each
• Gate leaf realignment with hinge/post correction: $200-$400 depending on the post’s condition

What moves the price is whether the post has shifted, whether you need a board instead of a component repair, and how far the gate has drifted out of alignment. We quote the job before we start, and that price holds. Estimates are free, and if you have a written estimate from another company, we’ll give you a free second opinion.

Why Van Nuys Homeowners Call Gatewood Fence & Gate for Linear Work

Hal Gatewood has been fixing gates in Van Nuys since 2001. He grew up off Sepulveda Boulevard and learned welding and metal fabrication at Los Angeles Valley College over in Valley Glen before spending two-plus decades working on the Valley’s gates. His name is on the shop and on every invoice. That means something when the person who quoted your repair is the same person who shows up to do it.

We hold a 90-Day Done Right Promise on every job, spelled out in writing. If it’s not right, one call brings us back. We answer the phone 24/7 with a live person. And because Van Nuys gates run everything from Linear to LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, we can service whatever else is on your property without referring you to someone we wouldn’t vouch for ourselves.

FAQs