Linear Gate Parts & Welding Nationwide | Gatewood Fence & Gate

Linear Gate Parts & Welding in Van Nuys: What to Know First

We provide independent Linear gate parts and welding in Van Nuys, and most jobs are done in a single visit because we carry the common failure parts on the truck and weld on site. A typical Linear hinge or post repair runs $180 to $475 depending on what actually failed, and you get the exact number before we touch a tool, not after. If you own a Linear gate that is sagging, grinding, or refusing to close, call (951) 749-5734 and a live person answers, day or night.

Call (951) 749-5734

This page is written for Van Nuys homeowners and property managers who have a Linear operator or Linear gate hardware and want to know what is actually wrong with it and what it costs to fix. Not a brochure. Just how we see these gates fail around here and what we do about it.

How Linear Products Fail – and How We Fix Them

• Linear MegaCode and Multi-Code receiver boards cooking in Van Nuys heat. The electronics on older Linear swing and slide operators sit in a metal box that faces the afternoon sun, and we regularly pull boards out of Van Nuys gates that have swollen capacitors from years of 100-degree days. The gate still has power but won’t respond to a remote. We replace the board with a quality OEM or matched aftermarket unit and re-seal the enclosure so it breathes instead of bakes.
• Linear LRA and SLR arm brackets ripping off the gate frame. The actuator bracket is only as strong as what it’s bolted to, and on welded steel pedestrian gates the bracket gets torn loose when a wind gust slams the gate or a delivery truck clips it. We weld the bracket back to the gate frame, reinforce the tubing if it has torn, and re-anchor the operator so the whole thing moves as one piece again.
• Hinge posts on Linear double-swing driveway gates migrating in soft Van Nuys soil. A two-leaf ornamental steel gate is heavy, and the clay soil around Van Nuys shifts with every wet winter and dry summer. The post leans, the gate drags, and the Linear operator strains itself trying to move a gate that is binding. We don’t just re-hang the leaf. We dig the post, set it square in new concrete, re-weld the hinge barrels when they have egged out, and only then re-tune the Linear limits.
• Linear slide gate rollers and track wearing uneven because the concrete settled. We see V-track rollers on Linear slide gates that have flat-spotted on one side because a section of the concrete track sank half an inch. The gate grinds and the operator trips its obstruction sensor constantly. We level the track section, replace the rollers with the right size for the existing rail, and re-set the Linear travel limits so the operator is not fighting a crooked road.
• Linear access keypads and locks failing from corrosion, not from age. The Linear AM-KP keypad and the electric locks on Van Nuys pedestrian gates sit outside in morning fog off the 405 and dust from Sepulveda Boulevard. Contacts corrode, buttons get intermittent, and the lock solenoid sticks. We clean or replace the keypad, free up or swap the lock, and make sure the wiring at the hinge point has not chafed through from a decade of opening and closing.

Our Linear Gate Parts & Welding Process

1. 1
   You call, a person answers. Hal or one of the crew takes the call at (951) 749-5734, asks what the gate is doing, and schedules a time we will actually be there. No call center three states away.
2. 2
   We show up and look at the whole gate, not just the part that failed. A Linear operator that keeps reversing usually is not the operator’s fault. It is a hinge binding or a post leaning. We find the root cause before we quote anything.
3. 3
   You get a written price before any work starts. We give you the exact number for parts and labor, and it does not change at the door. If you have another written estimate, bring it and we’ll give you a free second opinion on it.
4. 4
   We repair or replace with the right part. For Linear operators we use OEM parts when they matter for compatibility, and quality aftermarket equivalents when they are genuinely better value. We will tell you which is which and why.
5. 5
   Welding happens in your driveway, on site. Broken hinge, torn bracket, cracked rail, bent post – we weld it where it stands. The gate stays in Van Nuys, not hauled off to some shop.
6. 6
   We test it like we’re the one who has to live with it. We cycle the gate, check the safety reverse, adjust the Linear force and limit settings, and only leave when it runs clean and quiet. Then we hand you the 90-Day Done Right Promise in writing.

What Linear Gate Parts & Welding Costs in Van Nuys

Most Linear gate welding and parts jobs in Van Nuys land between $180 and $475 for a single repair. Here is the breakdown we quote from:

• Hinge replacement or re-welding (single gate): $180 – $320, depending on whether we are replacing the hinge or re-welding the existing barrel and gusseting the post.
• Post straightening or replacement with re-set in concrete: $350 – $650 for a single post dug out, set square, and welded back into the gate run.
• Rail or frame crack repair (welded on site): $150 – $300 per crack, including grinding, weld, and touch-up paint.
• Linear operator bracket or arm re-weld and re-mount: $200 – $400, including re-tuning the operator travel and force limits.
• Gate roller replacement and track leveling (Linear slide gates): $250 – $500 for pairs of rollers plus track section work.
• Latch, lock, or keypad replacement: $120 – $280 depending on the part and whether we are matching an existing Linear access system.

What moves the price is steel thickness, how far out of square the gate has gotten, and whether the post is salvageable. We quote it all upfront, and every repair over $200 takes $40 off with our standing offer. Call (951) 749-5734 for an exact number on your Linear gate. The estimate is free, and if it is inside the county, so is the trip.

Why Van Nuys Homeowners Call Gatewood Fence & Gate for Linear Work

Hal Gatewood has been fixing gates around Van Nuys since 2001, and his name is on the shop. That is not a metaphor. It is a building you can drive to and a person you can look in the eye. We repair Linear gates other companies want to replace, because a sagging post or a torn weld does not mean the whole gate is junk. We carry parts for Linear operators on the truck, and we also service the other big names around here – LiftMaster, Mighty Mule, Ghost Controls, and DoorKing – so when a property has mixed brands, one call handles all of it.

Every job carries the 90-Day Done Right Promise in writing. If it is not done right, Hal comes back and makes it right. No runaround. No fine print. And when you call, a live person answers 24/7. Not a voicemail. Not a chatbot. The person who shows up is background-checked, uniformed, and certified on nine major gate brands including Linear. We have been doing this for over 29 years, and the truck still parks in Van Nuys every night.

FAQs