FAAC Gate Installation Nationwide | Gatewood Fence & Gate

FAAC Gate Installation in Van Nuys: What to Know First

FAAC gate installation in Van Nuys typically runs between $1,800 and $4,200 for a complete residential swing or slide system, depending on gate size, operator model, and whether we’re building new or replacing existing hardware. As an independent FAAC service provider, Gatewood Fence & Gate installs, retrofits, and repairs FAAC swing and slide operators throughout the San Fernando Valley, usually completing a standard installation within one to two days once we have the equipment in hand. The honest truth: we quote the job upfront, in writing, before any work starts, and the number we give you is the number you pay.

Call (951) 749-5734

This guide is for Van Nuys homeowners who own a FAAC operator or are considering one, and who want the installation done right the first time, without a sales pitch. If you already know what you need, call us at (951) 749-5734 and we’ll come out, look at the gate, and tell you straight what it will take. If you’re still figuring things out, keep reading.

How FAAC Products Fail - and How We Fix Them

FAAC builds solid operators. We’ve installed and repaired enough of them over the years to know exactly where they give out, and it’s rarely where the manufacturer’s brochure would lead you to believe. Here’s what we actually see on FAAC gates around Van Nuys:

• Swing gate sag at the hinge post on FAAC 400 and FAAC 750 operators. The operator isn’t the problem. The post shifts, the gate leans, and suddenly the FAAC operator is fighting a gate that doesn’t want to move. We don’t just limit-switch our way around it. We dig out the post, re-set it in fresh concrete, and weld or bolt the hinges square. Then the operator does its job without burning itself out.
• FAAC 770 and FAAC C720 slide gates losing position after power outages. These are smarter operators, but they rely on a limit system that can drift if the gate track shifts even half an inch. We see it after heavy rain in Van Nuys when the soil under the track settles. We true the track, reset the limits, and teach the board where home position is. No unnecessary board replacement.
• Capacitor failure on older FAAC 412 and FAAC 422 swing operators. The number one call we get on these is a gate that hums but won’t move. That’s almost always the start capacitor. Some outfits will quote a full operator swap. We replace the capacitor, check the motor’s amp draw, and send you back to normal operation for under $200. That’s the difference between a repair shop and a sales outfit.
• Plastic gear wear on FAAC 540 and FAAC 844 slide operators. These units use a driven gear that eventually strips, especially if the gate was never lubricated properly. The telltale sign is a grinding noise that gets worse in hot weather. We stock both OEM and quality aftermarket gears and we’ll tell you the difference: OEM costs more, but it’s dimensioned exactly to spec. Aftermarket can save you 30 to 40 percent and we’ve seen them last just as long when the gate is aligned right.
• Photobeam misalignment on FAAC 740 and other slide setups. This one isn’t a FAAC defect so much as a heat and vibration issue. Van Nuys summers sit at 95 plus, the metal brackets expand, and suddenly the gate won’t close and the keypad just blinks at you. We see homeowners futzing with the beams for hours. We come in, remount them on solid, heat-stable hardware, and align them once. That usually ends the problem for good.

Our FAAC Gate Installation Process

We’ve installed FAAC operators on driveway gates, pedestrian gates, sliding gates, swing gates, double gates, and security gates across Van Nuys and the surrounding Valley. Here’s how a typical job goes from first call to a closing gate:

1. 1
   You call, a live person answers. Not a voicemail tree, not a call center. Someone here picks up the phone, asks where you are and what the gate is doing. Hal Gatewood or a member of his crew. If we can diagnose it over the phone, we’ll tell you so.
2. 2
   We come out and inspect the whole gate, not just the operator. Free estimate. No trip charge inside the county. We look at the posts, hinges, ground clearance, panel weight, and the operator’s condition. A FAAC operator installed on a bad post will fail in a year. We don’t set you up for that.
3. 3
   We lay out the real options. If the existing FAAC operator can be saved with a real repair, we say so. If replacement makes more sense, we’ll tell you that too, and we’ll quote OEM versus quality aftermarket parts with the tradeoffs explained. No pressure, no vague “we’ll see when we get in there” pricing.
4. 4
   We install, weld, and wire. This is where our on-site welding matters. We fabricate brackets, reinforce posts, and set everything square in your driveway. The gate doesn’t leave your property. The welder comes to you.
5. 5
   We test the full cycle - safely. We run the gate through opens, closes, obstacle detection, and manual release. We check the force settings so a kid can’t get pinned. We adjust until the gate closes the same way every time, no flinching, no grinding.
6. 6
   We hand you the guarantee in writing. The 90-Day Done Right Promise. If it’s not done right, we make it right. One call brings us back.

What FAAC Gate Installation Costs in Van Nuys

Here’s what we typically see on FAAC jobs in the Van Nuys area, with real numbers so you know what to expect before anyone sets foot on your driveway:

What moves the price is the gate itself: panel weight, post condition, whether the existing track or hinges are usable, and whether we’re running new conduit for power and safety edges. We always quote the job before we start, and that quote holds. Estimates are free. Call (951) 749-5734 and we’ll give you the real number for your gate.

Why Van Nuys Homeowners Call Gatewood Fence & Gate for FAAC Work

We’ve been at this since 2001, and the shop is right here, with our name on it and our address published for anyone to look up. Hal Gatewood grew up off Sepulveda Boulevard, not far from the old Van Nuys Airport, and he never left. He learned welding and metal fabrication at Los Angeles Valley College over in Valley Glen, then spent years on real jobs before opening Gatewood Fence & Gate. His dad was a weekend welder who kept the garage full of scrap metal and half-finished projects, and Hal kept the habit. There’s still a magnet on his truck bumper, just like his dad’s.

We carry parts and service for FAAC, LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, which means we fix what’s in front of us rather than telling you the whole system needs replacing. Every job comes with the 90-Day Done Right Promise in writing. Calls are answered by a live person around the clock. And we show up when we say we will. The name is on the shop, and the shop is down the road - that’s the oldest accountability there is.

FAQs