Elite Gate Parts & Welding Nationwide | Gatewood Fence & Gate

Elite Gate Parts & Welding in Van Nuys: What to Know First

We provide independent Elite gate parts and welding service in Van Nuys, with most hinge replacements, post work, and rail repairs done same day or next morning depending on parts. The honest price posture is this: a hinge replacement on an Elite gate typically runs $250-$450 in Van Nuys, a post reset runs $400-$750, and custom welding work gets quoted after we look at it, not over the phone. You’ll know the number before we start, and that number is what you pay.

Call (951) 749-5734

This page is for homeowners in Van Nuys who own an Elite gate and need somebody who understands how these gates actually fail. If your Elite gate is sagging, dragging, or refusing to latch, call (951) 749-5734 and we’ll talk it through. A live person answers, and that person works here.

How Elite Products Fail - and How We Fix Them

• Elite SL3000 and SL3000UL series: hinge weld fatigue at the post. These are sturdy slide gates, but Van Nuys heat plus the constant vibration of the roller carriage puts pressure on the hinge welds over the years. What we see most often is a crack forming right where the hinge plate meets the post, not in the gate panel itself. We grind the crack out, re-weld it on site, and add a gusset plate so it doesn’t just crack again six months later. That’s the difference between a patch and a repair.
• Elite Mirage and Estate Swing series: hinge bushing wear that masquerades as a gate problem. When the bronze bushings inside the hinge barrel wear out, the gate tilts and sags, and owners assume the whole panel is shot. It usually isn’t. We replace the bushings or the hinge assembly, re-hang the gate, and in most cases that gate has another ten years in it. A lot of companies would sell you a new gate here. We won’t.
• Elite heavy cantilever gates: roller carriage failure from Van Nuys grit and dust. The Valley doesn’t get much rain, but what it does get is a fine dust that works into the roller bearings, especially on the carriage assemblies that slide these big gates. The symptom is a gate that jerks and shudders on the track. The fix is replacing the rollers and cleaning the track, sometimes re-welding the carriage mount if the play went on too long. We carry common Elite roller sizes in the truck.
• Elite latch and catch misalignment on swing gates. This one shows up as a gate that won’t stay latched, or a latch that grinds when it closes. In Van Nuys specifically, the soil shifts with the wet-dry cycle through the year, and the gate post moves just enough to throw the latch off. We realign the catch, re-weld the latch plate if it’s been stressed, and the gate closes like it’s supposed to.
• Elite panel sag we can actually fix by addressing the post, not the panel. A gate sags in the hinge post, not in the middle. That’s not a quirk of Elite gates, it’s true of every gate ever hung, but we see it constantly on Elite swing gates in Van Nuys because the original installers often set the post in a small concrete footer that wasn’t sized for the gate mass. We dig, set the post deeper with a proper footing, re-weld the hinge mounts, and the gate hangs true again.

Our Elite Gate Parts & Welding Process

1. 1
   You call, we answer. A live person picks up at (951) 749-5734 and asks the right questions: which Elite series you have, what the gate is doing, and whether it’s hung up, sagging, or making noise.
2. 2
   We show up in the window we promised. We look at the gate in your driveway, not photos. Hal grew up off Sepulveda Boulevard and has been doing this in Van Nuys since 2001, so he’ll probably know your street.
3. 3
   We tell you exactly what’s wrong and what it’ll cost. If it’s a bushing versus a cracked weld, you hear which one it is and why. The price is set before any work begins, and there’s no trip charge inside the county.
4. 4
   We make the parts call together. If your gate calls for an OEM Elite part, we order it. If a quality aftermarket part does the same job for less, we tell you that too and let you decide. We won’t put a cheap part on your gate without saying so.
5. 5
   We weld and repair on site. The gate stays in your driveway. No hauling your gate off to a shop, no “we’ll call you in two weeks.” Most Elite parts and welding jobs in Van Nuys are done in one visit.
6. 6
   We test it and stand behind it. Open, close, latching, tension, tracking. We run the gate through its paces before we call it done. Then the 90-Day Done Right Promise goes out in writing. If it’s not right, we make it right.

What Elite Gate Parts & Welding Costs in Van Nuys

Here are the real numbers we quote on Elite work in Van Nuys, and these don’t change when we get to your door:

• Hinge replacement (single hinge, standard Elite swing gate): $150-$325
• Complete hinge set with re-hang and alignment: $350-$600
• Post replacement or deepening (dig, set, re-weld hinge mounts): $400-$750
• Rail repair or reinforcement welding: $180-$380
• Custom welding (crack repair, gusset plate, bracket fabrication): $120-$300 per weld point, quoted after inspection
• Gate roller replacement (including carriage inspection): $175-$325
• Latch and lock re-alignment or plate re-welding: $125-$250

What moves the price is three things: how far the post has moved, whether we need to bring in heavier steel for the repair, and whether the part has to be ordered from Elite or we have it on hand. We’ll show you the breakdown before we touch anything, and there’s a $40 break on any repair over $200, plus a permanent 10% discount for seniors and veterans. Call (951) 749-5734 and we’ll give you a straight answer.

Why Van Nuys Homeowners Call Gatewood Fence & Gate for Elite Work

Because we’re here. The name on the shop is Hal Gatewood’s, and the shop has a published address you can drive to. We’ve been at this in Van Nuys since 2001, and we handle Elite gates alongside LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so when your Elite gate has a problem that involves the operator too, we fix the whole thing in one visit instead of sending you to someone else. The 90-Day Done Right Promise is stamped on every invoice, not hidden in the fine print. And if you ever want to look the person in the eye who’s going to work on your gate, just come by the shop. That offer has never been a problem for me to make, and it never will be.

We fix what’s broken, we don’t sell you a new gate because it’s easier for us. That’s the whole difference.

FAQs