FAAC Gate Access Control Nationwide | Gatewood Fence & Gate

FAAC Gate Access Control in Van Nuys: What to Know First

FAAC gate access control repair in Van Nuys typically runs $160 to $480 for keypads, card readers, and phone entry systems, with most jobs turned around same day by an independent technician who carries FAAC-compatible parts in the truck. We’re an independent FAAC service provider, not an authorized dealer, which means we work for you, not the manufacturer’s warranty clock. This page is for homeowners and property managers in Van Nuys, Valley Glen, Sherman Oaks, Encino, and the surrounding San Fernando Valley who own a FAAC gate operator or access control panel and want it diagnosed honestly. Call (951) 749-5734 and Hal or a member of his crew will answer.

Call (951) 749-5734

How FAAC Products Fail - and How We Fix Them

FAAC builds solid equipment, but Van Nuys heat, dust, and hard water do things to gate access control that the factory manuals never mention. Here’s what we actually see on service calls:

• FAAC E124 keypad membrane delamination. The rubberized buttons on the E124 look fine until a July afternoon hits 105 degrees, then the adhesive backing lets go and the keypad starts registering ghost presses. We’ve opened panels in Van Nuys where one wandering digit was sending the gate into a loop at 3 a.m. We replace the membrane and reseal the housing so it holds through the next heat wave.
• XB 702 photocell misalignment on settling driveways. FAAC safety beams are picky about alignment, and Van Nuys soil expands and contracts with the rainy season. A beam that’s off by half an inch throws a fault the panel labels as “obstruction” when there’s nothing there. The fix is usually a bracket adjustment and re-leveling, not a new photocell. That’s a $90 adjustment versus a $300 part.
• Phone entry system corrosion on FAAC 424 D boards. The 424 D’s terminal strip collects moisture from sprinkler overspray and the morning marine layer. We see green oxidation on the relay contacts, which causes intermittent “no answer when called” complaints that drive homeowners crazy because the system works fine when we test it. We clean and reseal the board, replace the relay if it’s pitted, and move the enclosure away from the sprinkler line.
• Remote receiver drift on FAAC XR2 units near Van Nuys Airport. The XR2 receiver shares a frequency band with some aviation ground equipment, and homes east of the airport get interference that sends remotes from a 50-foot range to about 8 feet. We install a shielded antenna and retune the receiver to a clear channel. It’s a known issue in the neighborhood, not a bad remote.
• Smart access retrofit mismatches on older FAAC operators. When owners want app-based access on an FAAC 400 or 402 operator, they usually buy a generic Wi-Fi module that fights with the FAAC control board’s logic. The gate opens, hesitates, closes halfway, then reverses. We match the add-on module to the specific board generation and wire it through the proper input so the operator’s safety logic still runs the show.

Our FAAC Gate Access Control Process

Every FAAC job follows the same route, whether it’s a dead keypad or a full phone entry retrofit. No surprises, no guesswork.

1. 1
   Call and describe the symptom. Tell us what the gate does or won’t do. A live person answers, day or night, and we’ll ask about the model number if you can find it. Most FAAC units have it printed inside the cover or on the control board.
2. 2
   On-site diagnosis. Hal or a crew member drives out, tests the keypad, receiver, and board with a meter, and finds the exact fault before quoting a dime. We don’t guess over the phone and we don’t pad the job with parts that don’t need replacing.
3. 3
   Straightforward quote before any work starts. You get a price for parts and labor upfront, in writing. $40 off any repair over $200, no trip charge inside Los Angeles County. If you already have a written estimate from someone else, we’ll give you a free second opinion.
4. 4
   The repair, with the right part. We use OEM FAAC parts when the job calls for them, and quality aftermarket components when they’re functionally identical and cost less. We’ll tell you which is which and why, in plain English. Most keypad and receiver swaps happen on the spot in your driveway, because we bring the common FAAC parts with us.
5. 5
   Full testing and cleanup. We cycle the gate 20-plus times, test every remote and code, and check the safety edges and photocells before we call the job done. The work area gets swept, the panel cover goes back on straight, and we walk you through how to use the new access control.
6. 6
   90-Day Done Right Promise in writing. If anything we fixed or installed fails in the first 90 days, one call brings Hal back. No runaround, no service fee, no fine print. The promise is stamped on every invoice.

What FAAC Gate Access Control Costs in Van Nuys

All pricing in the table below reflects what we actually charge in Van Nuys as of early 2026. Every quote gets agreed before we unload a single tool, and the price we shake hands on is the price you pay.

• Keypad replacement or membrane repair (E124, DS24): $120-$280 installed, depending on the model and whether we can save the housing.
• Remote receiver repair or retune (XR2, RP2): $140-$320, including antenna work if the airport interference thing applies.
• Phone entry system repair (FAAC 424 D, GSM modules): $180-$450, with board cleaning and relay replacement in the common scenario.
• Full access control retrofit with card reader and keypad: $650-$1,400, including all hardware, wiring, and programming, depending on operator age and wire runs.
• Smart access integration (app or Wi-Fi control on existing FAAC operator): $350-$800, board-matched, not the generic module that fights your operator.

What moves the price: how old the FAAC board is, whether we can reuse existing wiring, and whether the failure is mechanical or electronic. Sometimes a “keypad problem” turns out to be a failing control board, and that changes the ticket. We’ll show you the test results before we recommend a board. Free estimates, no trip charge in the county. Call (951) 749-5734 for your number.

Why Van Nuys Homeowners Call Gatewood Fence & Gate for FAAC Work

Hal Gatewood has been repairing gates across the Valley since 2001, and his name is on the shop and every invoice. That’s a different kind of accountability than a rotating tech in a branded van. When a FAAC keypad fails in Van Nuys, you want someone who has opened a hundred of them, not someone reading a diagnostic flowchart on a tablet. We weld on site, we carry FAAC-compatible parts on the truck, and we service the other major brands too – LiftMaster, Mighty Mule, Ghost Controls, DoorKing – so if your property has a mix of operators, we handle all of it in one visit. Every job carries our 90-Day Done Right Promise in writing. Seniors and veterans get 10% off, permanently. We answer the phone 24/7 with a live person because when your gate won’t close at midnight, a voicemail doesn’t help.

FAQs