A Gatewood company - serving Van Nuys, CA

LiftMaster Gate Access Control Nationwide | Gatewood Fence & Gate

Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Styles & brands we work with

Wrought iron
Wrought iron
Wood & steel frame
Wood & steel frame
Farm & ranch
Farm & ranch
Sliding driveway gates
Sliding driveway gates
LiftMaster operators
LiftMaster operators

Before & after – our own jobs

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

LiftMaster Gate Access Control in Van Nuys: What to Know First

LiftMaster gate access control repair in Van Nuys typically runs $180 to $640 depending on whether we’re rebuilding a keypad, replacing a receiver board, or rewiring a phone entry system, and most jobs are done in one visit. We’re an independent LiftMaster service provider, which means we work on the equipment you already own without pushing you toward a full system replacement. If your keypad stopped talking to the opener or the entry phone rings but won’t release the gate, call (951) 749-5734 and we’ll give you a straight answer before we ever roll a truck.

Call (951) 749-5734

This page is for Van Nuys homeowners and property managers with a LiftMaster gate that needs access control work. Not the gate itself, but the stuff that tells the gate to open: keypads, remotes, phone entry boxes, card readers, video intercoms, and the smart modules that tie it all to your phone. If the gate opens manually but the keypad just sits there blinking, that’s access control. That’s us.

How LiftMaster Products Fail - and How We Fix Them

  • LA400 and LA500 keypads going dead after rain. Van Nuys gets maybe 15 inches of rain a year, but when it comes, these units take it hard. The factory gasket on the keypad face dries out after four or five seasons, and moisture wicks into the ribbon connector. The keypad still lights up, but the opener never sees the command. We replace the gasket, clean the connector, and seal the housing properly. Cheaper than a new keypad, and it lasts.
  • CAPXL and CAPXM phone entry systems dropping calls. LiftMaster’s cellular phone entry boxes rely on a SIM card that sits in a metal enclosure. Near Van Nuys Airport, some properties get weak signal, and the module keeps rebooting itself trying to find a tower. We relocate the antenna, check the SIM seating, and on older CAPXL units, we’ll reflash the firmware. That last part fixes more than half the “it worked last week” calls we get.
  • Security+ 2.0 remotes that won’t pair after a power blip. Same weak point across LiftMaster’s residential line. The receiver board on the control box loses its memory during an outage and the remotes all go dumb at once. It’s not the remotes. It’s the board. We reset and re-pair everything right there in your driveway, and we’ll tell you whether adding a small surge protector is worth the fifty bucks. Sometimes it is, sometimes the board’s already cooked.
  • MyQ smart access modules that work fine in the house and not at the gate. The MyQ hub was designed for garage doors ten feet from your router. At the gate line, the Wi-Fi signal is often too weak for the module to stay connected. We’ll mount the hub where it gets a usable signal, hardwire a repeater, or switch the system to LiftMaster’s cellular bridge. The gate goes back on your phone and stays there.
  • Card readers on commercial properties with intermittent reads. LiftMaster’s PPWR and card reader combos are common on Van Nuys apartment buildings and storage yards. The power supply’s capacitors degrade in the heat of an August afternoon, and the reader voltage sags just enough to miss a card swipe. We test the transformer under load, not just at the bench, and replace what’s actually tired instead of throwing a new reader at the problem.

Our LiftMaster Gate Access Control Process

  1. 1
    You call, a person answers. Not a phone tree. You tell whoever picks up what the system’s doing, or not doing. We’ll ask a few questions and usually tell you whether it’s likely a small fix or something bigger before we ever schedule the visit.
  2. 2
    We show up with the right parts for the job. We stock LiftMaster’s common access control components for the LA400, LA500, CAPXL, and MyQ lines on the truck. We also carry quality aftermarket parts where they make sense, and we’ll tell you the difference before we install anything.
  3. 3
    We diagnose the actual failure. We test the low-voltage side, the receiver, and the wiring between the access device and the opener. Half the time the problem isn’t the keypad or the phone entry box, it’s a corroded splice or a ground fault in the conduit run. We’ll find it and show you.
  4. 4
    We give you the price before we turn a wrench. Fixed dollar amount, agreed up front. No hourly meter running while we scratch our heads. If we find something else wrong inside the job, we stop and tell you before adding a dollar.
  5. 5
    We fix it, test it, and make you watch it work twice. Or three times. We’ll stand there and run the keypad, the remote, the phone app, whatever you have. Nobody drives off while the gate’s still latching soft.
  6. 6
    You get the 90-Day Done Right Promise in writing. If it acts up again within ninety days, call and we come back. That’s the whole promise. No fine print.

What LiftMaster Gate Access Control Costs in Van Nuys

Here’s the honest range for the LiftMaster access control work we do most in Van Nuys:

Job Typical Price Range
Keypad repair or rebuild (LA400/LA500) $180 - $320
Keypad replacement with programming $340 - $480
Receiver board repair or remote re-pairing $150 - $260
Phone entry repair (CAPXL/CAPXM) $220 - $520
MyQ or smart access module setup and repair $190 - $380
Full access control upgrade with video intercom $640 - $1,300

The price moves based on whether we’re repairing existing hardware or replacing something that’s done for, how far the wire run is from the control box to the access point, and what kind of access device you want on the other end. Every quote is a fixed number you agree to before the work starts. Call (951) 749-5734 for a free estimate on your exact setup.

Why Van Nuys Homeowners Call Gatewood Fence & Gate for LiftMaster Work

I’m Hal Gatewood. I grew up off Sepulveda Boulevard, not far from the old Van Nuys Airport, and I’ve been fixing gates around the Valley since 2001. The name’s on the shop and my number’s the one that rings. When you call, a person answers. When we schedule a window, we’re there. And when the job’s done, you get the 90-Day Done Right Promise in writing, because my father’s rule was simple: if you wouldn’t stand behind it, don’t stand next to it.

We work on LiftMaster all day, but if that’s not the fix and your property has a Mighty Mule, Ghost Controls, or DoorKing system, we’ve got experience there too. We’re certified to service nine major gate brands, which matters when a property has more than one opener or the original controller gave out and you’re weighing repair against replacement. We’ll give you the straight answer, and we’ll fix what’s actually broken instead of selling you a whole new system to make the numbers look better.

FAQs

Need Gate Repair help in Van Nuys? Licensed & insured · 1-hour response · free estimates
Call (951) 749-5734
Local Service Coverage

Request a Free Estimate in Van Nuys

Tell us what you need - Gatewood Fence & Gate responds fast. No obligation.

By sending this request, you accept our Privacy Policy and authorize us to contact you via phone, email, or SMS about your request, including by the independent professionals who may fulfill it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch